manualshive.com logo in svg

Oki C810, Руководство по обслуживанию

Поделиться
Скачать
Oki C810 Скачать руководство пользователя страница 128

44015503TH  Rev. 1 

127 /

Oki  Data  CONFIDENTIAL

5.  MAINTENANCE MENUS

5.3.2  self-diagnostic mode

This section describes LEvEL 0 and LEvEL 1.

5.3.2.1  operator Panel

The  following  description  on  operating  the  self-diagnostic  is  provided,  premised  on  the 

following operator panel layout:

Self-diagnostic 

mode layout 

(entire)

(1)  Menu option display switching

 

The  level  in  a  shaded  area  (  XXXXX   )  can  be  displayed  only  from 
another one.

 

Use the MENU up-arrow ( ) or MENU down-arrow ( ) button to display 

the menu option shown in a non-shaded area (  XXXXX  ).

LEvEL0- engine status 

display

Engine status display

(Heater temperature)

(Environmental temperature 

and humidity display)

voltage display during printing 

(TR, CH, DB and SB)

Toner sensor

Error detail

LEvEL1-ENGINE DIAG MODE XX.XX

SWITCH SCAN

MOTOR & CLUTCH TEST

TEST PRINT

REG ADJUST TEST

DENS ADJ TEST

CONSUMABLE STATUS

PRINTER STATUS

FACTORy MODE SET

SENSOR SETTING

LED HEAD DATA

POWER ON

Normal operation mode

MENU up-arrow ( ) and 

ONLINE held down in 

combination (for three 

sec.)

MENU up-arrow ( ),

 MENU down-arrow ( ), 

ENTER and BACK 

pressed in combination

No buttons pressed

MENU up-arrow ( ), MENU down-arrow ( ) and 
HELP combination used until System Maintenance 
menu appears, and ENGINE DIAG MODE selected 
and ENTER pressed

LEvEL0

(1)  Menu option display switching

 

Hold down the BACK or ONLINE button or momentarily press the MENU up-arrow 
( ) or MENU down-arrow ( ) button to display the option shown in a shaded area  

(  XXXXX  ).

 

Use the MENU up-arrow ( ) or MENU down-arrow ( ) button to display the menu 

option shown in a non-shaded area (  XXXXX  ).

voltage display during 

printing

Transfer (TR) voltage (1) *1

Transfer (TR) voltage (2) *1

Charge (CH) voltage

Supply (SB) voltage

Development (DB) voltage

Environment level

After time-dependent 

adjustment

Before time-dependent 

adjustment

value of time-dependent 

adjustment

MENU up-

arrow ( ) 

MENU 

down-

arrow ( )

*1: Pressing the CANCEL button switches the voltage, which is displayed for a color, 

to that for another color.

Toner sensor

Toner sensor 

status monitor 

display

Motor control evaluation 

function

Registration motor 

constant-speed timer 

value and environmental 

humidity

Fuser motor constant-
speed timer value and 

target fuser temperature

Image drum motor 

constant-speed timer 

value

Belt motor constant-speed 

timer value

BACK held down (for two sec.)

ONLINE held down (for two sec.)

Error detail

Appropriate display, such as 

error code display

Engine status display

Heater temperature

Environmental 

temperature and humidity

Setting table

Transfer voltage

Transfer-off voltage and 

belt temperature

Side thermistor

MENU up-

arrow ( ) 

MENU 

down-

arrow ( )

Содержание C810






























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды