Oki C810 Скачать руководство пользователя страница 26

Страница: 26 / 253

44015503TH Rev. 1

25 /

Oki Data CONFIDENTIAL

2. DESCRIPTION OF OPERATION

outline of color registration correction

The color registration is corrected by reading correction patterns that are printed on the belt

with the color registration sensors located inside the sensor shutter under the belt unit. These

sensors are used to detect and correct color registration.

Automatic start timing of color registration correction

• At power-on

• When the cover is closed after it is opened for five seconds or more

• When 400 pages or more have been printed after the previous correction

A correction error may be issued due to an inadequate toner amount of the pattern

generated, a sensor stained with toner, deficient opening/closing of the shutter, or for other

reasons. However, even if an error is issued, it is not indicated on the operator panel.

Therefore, forcible color registration correction will have to be performed in the self-diagnostic

mode (section 5.3.2.6) to check the error indication.

Right color registration correction pattern

Left color registration correction pattern

Color registration sensor

Belt waste toner box

Belt cleaning blade

Color registration sensor

Transport belt

Sensor shutter

Содержание C810






























































































































































































































































Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды

Oki C810, Руководство по обслуживанию

Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды