Oki C810 Скачать руководство пользователя страница 131

Страница: 131 / 253

44015503TH Rev. 1

130 /

Oki Data CONFIDENTIAL

5. MAINTENANCE MENUS

5.3.2.3 switch scan test

The switch scan test is used for checking entrance sensors and switches.

1. Enter the self-diagnostic mode (level 1) and, until SWITCH SCAN appears on the

upper display, press the MENU up-arrow ( ) or MENU down-arrow ( ) button (the

MENU up-arrow ( ) button displays the next test option and the MENU down-arrow

( ) button displays the preceding test option). Then press the ENTER button.

SWITCH SCAN

2. Press the MENU up-arrow ( ) or MENU down-arrow ( ) button until an option

shown in table 5-3 for the unit to test appears on the lower display (the MENU up-

arrow ( ) button displays the next option and the MENU down-arrow ( ) button

displays the preceding option).

3. Press the ENTER button. The switch scan test starts, the unit’s name and current

status being displayed

PAPER ROTE:PU

1=H 2=L 3=H 4=L

Operate the unit (figure 5-1). Display information on applicable LCD display (the

information displayed vary depending on the sensor.

4. Press the CANCEL button. The state in step 2 is restored.

5. Repeat steps 2 through 4 when necessary.

6. Press the BACK button to end the test (the state in step 1 is restored).

Entrance sensor 1

Entrance sensor 2

Write sensor

Exit sensor

Tray-1 paper-end
sensor

Color registration
sensors L and R,
and density sensor

Belt thermistor

K toner sensor

K RFID
antenna

y RFID
antenna

M RFID
antenna

C RFID
antenna

y toner sensor

M toner sensor

C toner sensor

Fuser thermistor
upper sensor-side

Heater frame thermistor

Fuser
thermistor-lower

Image drum up-down sensor

Temperature and
humidity sensor

Duplex-in
sensor

Duplex
cover-open
sensor

Duplex bottom
sensor

Fuser
release sensor

Duplex rear
sensor

Duplex front sensor

Tray-2 entrance sensor

Second-tray
hopping sensor

Third-tray hopping
sensor

Second-tray size
setting switch

First-tray size
setting switch

Tray-2 paper-end sensor

Tray-3 entrance sensor

Third-tray size
setting switch

Tray-3 paper-end sensor

Cover-open switch

Fuser-in
sensor

Figure 5-1: Switch sensor locations

Содержание C810






























































































































































































































































Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды

Oki C810, Руководство по обслуживанию

Результаты поиска

Содержание C810

Отзывы:

Бренды по названию

Популярные бренды