Oilon EasyAce Скачать руководство пользователя

Страница: 22 / 54

Device settings → Hot water → Settings → Legionella inhibition

Status view → Hot water → Settings → Legionella inhibition

Time between starts

The interval between heating periods. This interval depends on the domestic hot

water temperature setting.

●

Typical setting: 3–7 days

● With lukewarm domestic hot water, use a shorter interval.

Inhibit start time

The time of day when the function is activated. Select a time when domestic hot

water is not typically used, such as nighttime hours.

Time to next start

The number of days (d) before the function is activated again.

3.5 Other settings

Device settings → Usage info

This option shows usage information across the unit’s entire operating history as well as for the current

year and the previous three full years.
Heating

An estimate of the space heating energy produced.

Hot water

An estimate of the energy produced for heating domestic hot water.

Electricity

An estimate of the compressor’s and the electric heater’s power consumption.

Additional heating

An estimate of the electric heater’s power consumption.

Compressor running

time

The number of hours the compressor has been in operation.

Compressor times

started

The number of times the compressor has started.

Device settings → Usage info → Current year

Heating

An estimate of the space heating energy produced within the current year.

Hot water

An estimate of the energy produced for heating domestic hot water within the current

year.

Electricity

An estimate of the compressor’s and the electric immersion heater’s power

consumption within the current year.

History

The above information shown for the previous three full years, broken down by the year.

Device settings → Heating circuits

See section

Heating.

Device settings → Hot water

See section

Domestic hot water.

Device settings → Operating mode

Off

The heat pump’s compressor and electric immersion heater are off.

In use

The heat pump is on. The electric immersion heater can also be used (if allowed by

the operating mode).

Heat pump

Additional heater only

Only the unit’s internal electric immersion heater is used for heating. The

compressor and the brine circuit are not in use.

20 (49)

M8004 2308EN

Содержание EasyAce























































Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды

Oilon EasyAce, Руководство по эксплуатации

Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды