background image

4.2 Heating settings

Device settings → Service → Heating

The 

Heating buffer sensor

 setting determines the heat source used by heating circuits: either the heat

pump's condenser or a buffer tank. Select other circuit equipment from each circuit’s settings.

Not connected

The heat pump is connected directly to the building’s heating system without a

buffer tank. No buffer tank sensor is connected. There can be an (unpowered)

instantaneous water cylinder, but not a buffer tank regulated by the heat pump.

Heating buffer

sensor

Connected

The heat pump is connected to a buffer tank which is regulated by the heat pump.

The tank is equipped with a temperature sensor which is connected to the heat

pump. Any heating circuits in the system are connected to the buffer tank.

Buffer

Buffer tank temperature.

Device settings → Service → Heating → Compressor (no buffer tank)

Start delay

The compressor’s start delay in space heating. Once the delay has elapsed, the

compressor will start.

Typical setting, floor heating:

 concrete floors 120, wooden floors 80–60

Typical setting, radiator heating:

 80–40

● Increase the delay to extend the interval between starts and to have the

compressor run for longer at a time.

● The delay is properly set when room temperature stays even and the

compressor starts 2–3 times per hour.

The delay is based on degree minutes, and it applies when flow water temperature

is below its setpoint. Once the measured temperature is above the setpoint, the

delay will be reset.

● Delay calculation: flow setpoint – measured flow temperature.

Stop delay

The compressor’s stop delay in space heating. Once the delay has elapsed, the

compressor will stop.

Typical setting: approx. 5

● Increase the delay to have the compressor run for longer at a time.

● If the delay is greater than 0, flow water temperature can be above the setpoint.

The delay is based on degree minutes, and it applies when flow water temperature

is above its setpoint. Once the measured temperature is below the setpoint, the

delay will be reset.

● Delay calculation: flow setpoint – measured flow temperature.

Device settings → Service → Heating → Compressor (with buffer tank)

Heating setting

Flow temperature determined by the heating curve.

Start difference

This setting determines the threshold for starting the heat pump in relation to the

heating setting.

Negative value:

 The setting determines how much the temperature in the buffer

tank needs to fall below the heating setting before heating starts.

Positive value:

 The seting determines how much above the heating setting can

the temperature in the buffer tank be before heating starts.

Start limit

The heat pump will start heating the buffer tank when buffer tank temperature falls

below this temperature (heating setting – start difference value).

Stop difference

The stop difference determines how many degrees above the start limit the buffer

tank will be heated.

Stop limit

Once the buffer tank temperature exceeds this temperature (start limit + stop

difference), the heat pump will stop heating the tank.

Charging difference The amount by which the setpoint for the heating water used for heating the buffer

tank will be increased in relation to the stop limit.

Charging setpoint

The setpoint for the heating water which is used for heating the buffer tank.

Minimum

temperature

The minimum buffer tank temperature regardless of any other settings or the heating

curve.

M8004 2308EN

23 (49)

Содержание EasyAce























































Отзывы: