Oilon EasyAce Скачать руководство пользователя

Страница: 33 / 54

Device settings → Service → Electricity

System current

An estimate of the electrical current drawn by the unit.

● The estimated power consumption of the unit’s peripherals is also included in

the value.

Maximum system

current

The automation system maintains a constant estimate of the electrical current drawn

by the unit and its peripherals. Whenever possible, the system keeps this electrical

current value below the

Maximum system current

setpoint.

● Select based on the heat pump’s fuse (such as 16 A or 25 A)

Peripheral device

usage approx. 3-

phase

The automation system maintains a constant estimate of the electrical power drawn

by the unit’s peripherals, such as electric immersion heaters in external storage

tanks. This value is used for calculating the overall current drawn by the system.

Device settings → Service → Accessory settings

→ Room temperature → Heating circuit 1

You can install and set up a sensor for each heating circuit or use one shared sensor. To do this, enable

the same sensor input from each heating circuit’s settings.
Input selection

The input to which the indoor temperature sensor is connected. To enable room

temperature measurement, install an auxiliary controller (optional accessory) and

use EXT inputs.

Temperature

optimization

See section

Heating

The settings for Circuit 2 and 3 are identical to Circuit 1 settings.

Device settings → Service → Manual control

The

Manual control

view allows you to operate the brine pump, condenser pump and the system’s

valves manually.

Off

Manual operation is disabled.

Manual mode

In use

Manual operation is enabled.

Cooldown duration

If the compressor or another device that is controlled by the heat pump has a

cooldown, specify the cooldown here. A cooldown will prevent devices from starting

too frequently, preventing damage to the device or its controller (for example, the

compressor and its soft starter).

Control

The control setting for manual operation (pump speed, for example).

● Change-over valve:

is position B,

100%

is position A

Device settings → Service → Restore service settings

This function reverts all settings in the

Service

menu to factory defaults.

M8004 2308EN

31 (49)

Содержание EasyAce























































Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды

Oilon EasyAce, Руководство по эксплуатации

Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды