Oilon EasyAce Скачать руководство пользователя

Страница: 5 / 54

1 Introduction

1.1 EasyAce heat pumps

EasyAce heat pumps feature wireless connectivity, allowing you to manage and

monitor your heat pump both locally and remotely. In addition to the wireless touch

screen provided with the heat pump, you can connect to the EasyAce system by

downloading the simple-to use EasyAce app to your mobile device.

This manual provides comprehensive instructions for how to use your heat pump. This

includes instructions on how to connect your heat pump to a mobile device.

Using the touch screen for any other purpose may cause slowdowns or

interference in the use of the unit’s automation system, or prevent the

system from being used altogether.

1.2 Instructions and diagrams

Document

Designation

EasyAce

Quick guide

M8007

(34793602)

EasyAce

User manual

M8004

(34793603)

1.3 Basic concepts

Buffer tank

Heating circuit’s storage tank.

Brine

Liquid that circulates in the brine circuit (evaporator circuit), usually a mixture

of water and ethanol.

Brine circuit

The brine circuit is a long loop of pipe embedded in the earth filled with brine,

a cold mixture of ethanol and water. The brine circuit extracts heat from the

ground.

Brine pump

The brine pump circulates brine inside and between the brine circuit and the

heat pump.

Coefficient of

Performance, COP

Ratio between the electricity used by the heat pump and the heating

provided. If a heat pump’s COP is 3.5, it will generate 3.5 watts of heating for

every watt of electricity.

Condenser pump

Pump that circulates heat-transfer fluid (heating water) to the condenser to

warm up and from the condenser to the heating circulation.

Degree minutes

The heat pump has a degree minute counter that determines when functions

are activated and how long they remain active. The more a measured value

differs from a setpoint, the faster the related function will be activated.

● Example: The start delay for the in-line heater is 90 °Cmin. Flow

setpoint is 60 °C, and measured flow temperature is 45 °C. This gives a

temperature difference of 15 °C. Each minute, 15 °Cmin is deducted from

the counter. The in-line heater will switch on in 6 minutes.

M8004 2308EN

3 (49)

Содержание EasyAce























































Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды

Oilon EasyAce, Руководство по эксплуатации

Результаты поиска

Содержание EasyAce

Отзывы:

Похожие инструкции для EasyAce

Бренды по названию

Популярные бренды