OEM TUF-2000F Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 37

OEM TUF-2000F Скачать руководство пользователя страница 5

TUF-2000F User Manual

5

If the positive totalizer is turned off, the positive totalizer value shown on the screen

is the value prior to its turn off

M03

Display flow rate and NEG(negative) totalizer
If the negative totalizer is turned off, the negative totalizer value shown on the

screen is the value prior to its turn off

M04

Display date and time, flow rate. The date and time setting method is found in

MENU60

M05

Display energy rate(instantaneous Caloric)and total energy (Caloric)

M06

Display temperatures, inlet T1, outlet T2

M07

Display analog inputs, AI3/AI4, current value and its corresponding temperature

or pressure or liquid level value

M08

Display all the detailed error codes
Display working condition and system error codes. ‘R’ stands for normal, others

refer to Chapter for details.

M09

Display today’s total NET flow

M10

Window for entering the outer perimeter of the pipe
If pipe outer diameter is known, skip this menu and go to Menu 11to enter the outer

diameter

M11

Window for entering the outer diameter of the pipe. Valid range:0 to 18000mm.
Note: you just need to enter either the outer diameter in M11 or the peripheral in

M10

M12

Window for entering pipe wall thickness
You may skip the menu and enter inner diameter in M13 instead.

M13

Window for entering the inner diameter of the pipe
If pipe outer diameter and wall thickness are enter correctly, the inner diameter will

be calculated automatically, thus no need to change anything in the window

M14

Window for selecting pipe material
Standard pipe materials (no need to enter material sound speed ) include:
(0) carbon steel (1) stainless steel (2) cast iron (3) ductile iron (4) copper

(5) PVC (6) aluminum

,

(7) asbestos (8) fiberglass

(9) other( need to enter material sound speed in M15)

M15

Window for entering the pipe material speed, only for non-standard pipe materials

M16

Window for selecting the liner material, select none for pipes without any liner.
Standard liner materials(no need to enter the liner sound speed) include:
(1) Tar Epoxy (2) Rubber (3) Mortar (4) Polypropylene (5) Polystryol

(6)Polystyrene (7) Polyester (8) Polyethylene (9) Ebonite (10) Teflon
(11) Other (need to enter liner sound speed in M17)

M17

Window for entering the non-standard liner material speed.

M18

Window for entering the liner thickness, if there is a liner

M19

Window for entering the ABS thickness of the inside wall of the pipe

M20

Window for selecting fluid type
For standard liquids(no need to enter fluid sound speed) include:
(0) Water (1) Sea Water (2) Kerosene

«
...
3
4
5
6
7
...
»

Содержание TUF-2000F






































Отзывы:

Нет отзывов