manualshive.com logo in svg

OEM TUF-2000F, Руководство пользователя, Страница: 32 / 37

Поделиться
Скачать
OEM TUF-2000F Скачать руководство пользователя страница 32

TUF-2000F User Manual 

 

32

AOa

(cr) 

Output current ‘a’ mA at the AO output 
terminal.

 

AOa

(cr)(lf)Note 6 

BA1(cr)

 

Return the resistance for T1

 

±d.ddddddE±dd(cr)(lf)

 

 

 

 

 

 

 

BA2(cr)

 

Return the resistance for T2

 

±d.ddddddE±dd(cr)(lf)

 

BA3(cr)

 

Return current value of AI3 (0~20mA)

 

±d.ddddddE±dd(cr)(lf)

 

BA4(cr)

 

Return current value of AI4 (0~20mA)

 

±d.ddddddE±dd(cr)(lf)

 

BA5(cr)

 

Return current value of AI5 (0~20mA)

 

±d.ddddddE±dd(cr)(lf)

 

AI1(cr)

 

Return temperature at T1 input

 

±d.ddddddE±dd(cr)(lf)

 

AI2(cr)

 

Return temperature at T2 input

 

±d.ddddddE±dd(cr)(lf)

 

AI3(cr)

 

Return temperature /pressure value of 
AI

3 

±d.ddddddE±dd(cr)(lf)

 

AI4(cr)

 

Return temperature /pressure value of AI4 ±d.ddddddE±dd(cr)(lf)

 

AI5(cr)

 

Return temperature /pressure value of AI5 ±d.ddddddE±dd(cr)(lf)

 

ESN(cr)

 

Return the ESN (electronic serial number) 
of the flow meter

 

ddddddd

(cr)(lf) note 7 

N

 

Prefix  of an IDN-addressing-based 
networking, The IDN address is byte, 
range 0-253

 

Note 

8 

W

 

Prefix  of an IDN-addressing-based 
networking, The IDN address is word, 
range 0-65535

 

Note 

8 

P

 

Prefix of any commands for returns with 
check-sum

 

 

 

&

 

Commands connector to make a 
compounding command in one line.

 

Result commands should not exceed 
253 bytes long.

 

RING(cr)(lf)

 

Handshaking request from a modem

 

ATA(CR)(lf)

 

 
OK(cr)

 

Acknowledgement from a modem.

 

No action

 

 

 

Handshaking from the flow meter to 
modem.

 

AT(CR)(LF)

 

GA(cr)

 

Special command for GSM network. 

 

note

９

 

GB(cr)

 

Special command for GSM network.

 

note

９

 

GC(cr)

 

Special command for GSM network

 

note

９

 

Note: 

0.

（

cr

）

stand for carriage return, its ASCII value is 0DH. (lf) stand for line feed, its ASCII value 

is 0AH. 

1

．

d stand for a digit number of 0~9, 0 is expressed as +0.00 

Содержание TUF-2000F






































Отзывы:

Нет отзывов