manualshive.com logo in svg

OEM TUF-2000F, Руководство пользователя, Страница: 12 / 37

Поделиться
Скачать
OEM TUF-2000F Скачать руководство пользователя страница 12

TUF-2000F User Manual 

 

12

which stand for the total flow is over 100 cubic meters during the period of every 

day from 20:00 to 06:00, setups is like 
  M51 start time =20:00:00 
  M51 interval  =10:00:00 
  M51 log times =9999    (means always) 
    M80 select item #9 
  M81 input 100         (Unit is defined in M30,M31,M32) 

M81 

The built-in batch controller 
Set the flow batch value(dose) 
The internal output of the batch controller can be directed either to the OCT or the 

RELAY output circuits.     
M81 and M80 should be used together to configure the batch controller. 
Note: Because the measuring period is 500mS, the flow for every dos should be 

keeping at 60 seconds long to get a 1% dose accuracy. 

M82 

View the daily, monthly and yearly flow totalizer and thermal energy totalizer value.
The totalizer values and errors for the last 64 days, 32 last 32 months and last 2 

years are stored in the RAM memory, To view them, use the ‘ENT’ and ‘UP’ ‘Down’ 

keys. 

M83 

Automatic Amending Function for automatic offline compensation. 
Select ‘YES’ to enable this function, select ‘NO’ to disable it. 
When the function is enabled, The flow meter will estimate the average flow 

uncounted (or ‘lost’) during the offline session and add the result to the totalizer. 
The estimation of the uncounted flow is made by computing the product of the 

offline time period and the average flow rate, which is the average of the flow rate 

before going offline and the one after going on line. 

M84

 

Set the thermal energy unit: 

 

0. GJ        1. KC              2.KWh          3. BTU

 

M85

 

Select temperature sources

 

0.        from T1,T2 (factory default)

 

1.        from AI3,AI4

 

M86

 

Select the Specific Heat Value.

 

Factory default is ‘GB’. Under this setting, the flow meter will calculate the enthalpy 

of water based on the international standard.

 

If the fluid is other than water, you should select option ‘1. Fixed Specific Heat’, and 

enter the specific heat value of the fluid. 

 

M87

 

Turn on or turn off the Energy totalizer.

 

M88

 

Select thermal energy totalizer multiplying factor.

 

Factory default is ‘1’. 

 

M89

 

1. Display the temperature difference

 

2. Window for entering the lowest temperature difference.

 

M90 

Display signal strengths S (one for upstream and one for downstream), and signal 

quality Q value. 
Signal strength is presented by 00.0 to 99.9, the bigger the value, the bigger the 

signal strength will be, and more reliable readings will be made.   
Q value is presented by 00 to 99, the bigger the better. It should at least be great 

than 50 for normal operations. 

Содержание TUF-2000F






































Отзывы:

Нет отзывов