manualshive.com logo in svg

OEM TUF-2000F, Руководство пользователя, Страница: 21 / 37

Поделиться
Скачать
OEM TUF-2000F Скачать руководство пользователя страница 21

TUF-2000F User Manual 

 

21

For example, reading the registers from REG0001 to REG0010 in the unit #1 (ultrasonic flow 
meter) under the MODBUS-RTU format, the command could be as following 

01        03              00        00          00        0A                      C5            CD         

（

hex

）

 

Unit  Function   start  REG   Numbers of REGs     Check-sum 

While under the MODBUS-ASCII format, the command could be 

:01030000000AF2(CR and LF) 

 

 

Details about the standard MODBUS protocol will not be studied in this manual; please the 

users find them on other related materials. 

By default, the RS232/RS485 will setup with 9600,none,8,1(9600bd

，

none parity

，

8 data bits

，

 

1 stop bit) 

5.1.1 MODBUS REGISTERS TABLE 

  MODBUS REGISTERS TABLE for TUF-2000F 

（

please take notice the difference with the water meter MODBUS table

）

 

 

REGISTER NUMBER

VARIABLE 

NAME 

FORMAT 

NOTE 

0001-0002 

2 

Flow Rate 

REAL4 

Unit:  m

3

/h 

0003-0004 

2 

Energy Flow Rate 

REAL4 

Unit:    GJ/h 

0005-0006 

2 

Velocity 

REAL4 

Unit:  m/s 

0007-0008 

2 

Fluid sound speed 

REAL4 

Unit:    m/s 

0009-0010 2 

Positive 

accumulator 

LONG 

Unit is selected by 
M31, and depends 
on totalizer 
multiplier 

0011-0012 

2 

Positive decimal fraction 

REAL4 

Same unit as the 
integer part 

0013-0014 2 

Negative 

accumulator 

LONG 

Long is a signed 
4-byte integer, 
lower byte first 

0015-0016 

2 

Negative decimal fraction 

REAL4 

REAL4 is a format 
of Singular 
IEEE-754 number, 
also called FLOAT 

0017-0018 

2 

Positive energy accumulator 

LONG 

  

Содержание TUF-2000F






































Отзывы:

Нет отзывов