manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE FRDMGD3100HBIEVM, Руководство пользователя, Страница: 5 / 35

Поделиться
Скачать
NXP Semiconductors SAFE ASSURE FRDMGD3100HBIEVM Скачать руководство пользователя страница 5

NXP Semiconductors

UM11134

FRDMGD3100HBIEVM half-bridge evaluation board

UM11134

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2020. All rights reserved.

User guide

Rev. 3 — 10 February 2020

5 / 35

4.3 Device features

Table 1. Device features

Device

Description

Features

GD3100

The GD3100 is an advanced

single channel gate driver for

IGBTs.

•

Compliant with ASIL C/D ISO 26262 functional

safety requirements

•

SPI interface for safety monitoring, programmability

and flexibility

•

Compatible with current sense and temp sense

IGBTs

•

DESAT detection capability for detecting V

CE

desaturation condition

•

Fast short-circuit protection for IGBTs with current

sense feedback

•

Integrated Galvanic signal isolation

•

Integrated gate drive power stage capable of 15 A

peak source and sink

•

Interrupt pin for fast response to faults

•

Compatible with negative gate supply

•

Complimentary PWM/PWMALT controls for dead

time insertion

•

Independent fail-safe enable and fail-safe state

controls

•

Compatible with 200 V to 1700 V IGBTs, power

range > 125 kW

4.4 Board description

The FRDMGD3100HBIEVM is a half-bridge evaluation board populated with two GD3100

single channel IGBT gate drive devices. The board supports connection to a FRDM-

KL25Z microcontroller for SPI communication and programming, through the use of a

logic translator board. The board includes DESAT circuitry for short-circuit detection and

implementation of GD3100 IGBT shutdown protection capabilities.
The evaluation board is designed to connect to a single phase of an Infineon Hybrid

PACK Drive IGBT for evaluation of the GD3100 performance and capabilities.

Содержание SAFE ASSURE FRDMGD3100HBIEVM




































Отзывы:

Нет отзывов