nvent RAYCHEM ACS-30 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 145

background image

nVent.com

|

43

Raychem-AR-H58692-ACS30UIT2Programming-EN-1805

2.13. SYSTEM|RELAYS WINDOW

The System|Relays window lets you configure alarm relays.

Fig. 2.44

System|Relays window

There are three independent alarm relays in the ACS-UIT2 that can be used for remote annunciation
of alarms. Each relay can be programmed for a specific alarm type, multiple alarm types, or none. If
“Any Alarm” is chosen for a relay, any alarm condition will activate that relay.

2.14. SYSTEM|COMM WINDOW

The System|Comm window lets you set up communications with host systems.

Fig. 2.45

System|Comm window

The ACS-UIT2 can be connected to a Building Management System (BMS) or host computer using
an RS-485, RS-232, or 10/100Base-T Ethernet connection. All data and setup options are accessed
with communications that follow the Modbus (RTU/Modbus/TCP) protocol. To enable BMS
communications, please refer to the ACS-UIT2 Modbus Protocol document (H58685). ProtoNode
multi-protocol device servers are available through nVent. The ProtoNode is pre-programmed with
the Modbus mapping for ACS-30 and C910-485 controllers for BACnet, MetaSys and LonWorks
protocols.

IP Address/Subnet Mask

By default, the IP Address and Subnet Mask are automatically inserted. However, if the IP Address
or Subnet Mask needs to be changed, click on the IP Address or Subnet window and then on the
LAN91C1111 icon.

«
...
41
42
43
44
45
...
»

Содержание RAYCHEM ACS-30


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для RAYCHEM ACS-30

FPBA-01 PROFIBUS DP

Бренд: ABB Страницы: 2

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: NCR Страницы: 6

Бренд: Gantner Страницы: 56

Бренд: Lawler Страницы: 2

Бренд: VCON Страницы: 16

Бренд: Datavideo Страницы: 17

Бренд: Datamax Страницы: 22

Бренд: LAIA Страницы: 71

Бренд: Gardena Страницы: 14

Бренд: Gardena Страницы: 8

Бренд: Garaventa Lift Страницы: 58

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды