nvent RAYCHEM ACS-30 Скачать руководство пользователя страница 102

Страница: 102 / 145

nVent.com

102

Raychem-AR-H58692-ACS30UIT2Programming-EN-1805

3.8.2.

TEMP CONTROL – AMBIENT TEMPERATURE CONTROL

Fig. 3.78

Roof & Gutter - Ambient Temperature Control Window

The Ambient Temperature window allows you to control your Roof & Gutter application using
ambient temperature. Tap Ambient Control

Fig. 3.79

Setup|Roof & Gutter - Ambient Temp Control Window

Setpoint:

Enter the temperature setpoint for ambient control

Range:

30°F (-1°C)–50°F (10°C)

Default:

35ºF (2°C)

Deadband:

If the measured temperature is above the ambient or high temperature override setpoint

temperature plus deadband, the relay output is turned off. If the control temperature is below the
setpoint temperature, the output is turned on.

Range:

1°F (1°C)–10°F (5°C)

Default: 5ºF (3°C)

High Temperature Override:

The high temperature override is the setpoint that will override the

ambient control temperature. This is typically used as a gutter sensor.

Range:

40°F (4°C)–90°F (32°C)

Default:

55ºF (13°C)

Содержание RAYCHEM ACS-30


















































































































































Результаты поиска

Содержание RAYCHEM ACS-30

Отзывы:

Похожие инструкции для RAYCHEM ACS-30

Бренды по названию

Популярные бренды

nvent RAYCHEM ACS-30, Руководство по программированию

Результаты поиска

Содержание RAYCHEM ACS-30

Отзывы:

Похожие инструкции для RAYCHEM ACS-30

Бренды по названию

Популярные бренды