manualshive.com logo in svg

NTN K-ECK96, Инструкция по эксплуатации

Поделиться
Скачать
NTN K-ECK96 Скачать руководство пользователя страница 16

 

16

(5) Wiring of external control input   

 
 
 
 
 
 
 
 

 

Wiring method to control parts feeder

’

s ON/OFF from 

outside when the function is a standard setting, is 
explained. 

① 

Check that between 24V-+V terminals is short-circuited 
with jumper. In case jumper or control wire etc. is not in, 
short-circuit them 

② 

The jumper wire between terminals of X1 and 0V is 
removed, and the relay contact (or NPN transistor) is 
connected between these terminals. Do not remove 
jumper 1. 

※ 

When the ON/OFF delay timer is intended to be used, use the IN input. Please prepare cables used for 
control by your company. 

When function 

№

. JO2 is set as 1 (standard). 

・ 

With short-circuited state between X1

－

0V, parts feeder is driven (for NPN transistor output, it is Lo level) 

・ 

With open state between X1

－

0V, parts feeder is stopped (for NPN transistor output, it is High level) 

When the logic is reversed (JO2 is set as 0) by the function, it is driven with open state. Please refer to P.39 

for the setting of the function JO2. 

Please refer to the next page when controlling by the PNP transistor output or using it for the hopper control. 

Note 1

 

The current of DC24V 7mA flows between terminals X1-0V. Please be careful of the noise 

enough because it is a minute electric current. 

Note 2

 

The cable length of signal input line (24V, +V, X1, 0V) should be within 10m. Adopt a twist wiring if it is 

possible.

 

In case of no external control used 

When the external control terminal is not used, make function J02 setting as "1" and have the 

external control input terminal short-circuited (at two positions of 24V-+V and X1-0V). The controller 
drives continuously. Even if the setting of J02 is made "0" and the external control input terminal is 
opened, it becomes a continuous driving.

 

Caution 

24V, X1 and 0V terminals have polarity. Please be 
careful of wiring enough. In addition, please never 

connect it to AC power. 

Caution 

Parts feeder's ON/OFF control must use the 
external control input terminal. ON/OFF control by 
the power supply is impossible. 

制御用ケーブル

0V

X1

24V +V

ジャンパ１

3.3k

24V

ジャンパ２

Jumper 1

 

Jumper 2

 

Control cable

 

Содержание K-ECK96
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды