Novexx Solutions XLP 514 страница 71 Скачать руководство пользователя | Manualshive

Страница: 71 / 116

background image

User Manual

XLP 514/516

Related tasks

Positioning the label sensor

on page 72

XLP 51x with internal rewinder and dispensing edge: Inserting roll material

WARNING!
Danger of crushing fingers when closing the front hood.
► Always use the grip to open or close the front hood.

WARNING!
Danger of rotating parts drawing items in!
► Don´t wear loose long hair (if necessary, wear a hairnet).
► Keep loose jewellery, long sleeves, etc. away from rotating parts of the printer.
► Always close the front hood before printing.

WARNING!
The print head can become hot during operation!
► Be careful whenever touching the print head.

The illustrations in this chapter show a XLP 514. In case that the operation of the XLP 516 differs in

some points, this is indicated at the relevant point in the text

Before you begin

• Printer with internal rewinder and dispensing edge
• Rewound backing paper has been removed
• Internal rewinder is activated (

Options

>

Selection

>

Periph. device

= “Dispenser”)

• Printer is stopped (“Home” display)
• The label material is in roll form and is wound with the label side facing outwards (if this is not the

case, please note the deviating threading diagram)

Procedure

1.

Press the red button (A) on the dispensing edge to unlock the dispensing roll. Remove the dis-

pensing roll (B).

Edition 1 - 8/2021

71

Operation

Inserting and removing label material

«
...
69
70
71
72
73
...
»

Содержание XLP 514





















































































































Отзывы:

Нет отзывов

Похожие инструкции для XLP 514

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: Badger Meter Страницы: 16

Бренд: Datalogic Страницы: 48

Бренд: PageFlip Страницы: 32

Бренд: Xycom Страницы: 99

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

Бренд: Landoll Страницы: 70

Бренд: Landice Страницы: 19

Бренд: Landice Страницы: 7

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренд: Nel-Tech Labs Страницы: 8

Бренд: Parkside Страницы: 95

Бренд: A.HABERKORN Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды