Novexx Solutions XLP 514 страница 72 Скачать руководство пользователя

Страница: 72 / 116

User Manual

XLP 514/516

Insert the label web, see

XLP 51x standard: Inserting roll material

on page 65.

Remove the labels from the backing paper on a length of approx. 30 cm from the end of the label

web.

Move the backing paper to the rewinder as shown and fasten the end of the backing paper strip to

the clasp (A).

Put the dispensing roll back in place. To do this, first insert the axle of the roller into the bearing on

the left, then press it into the spring-loaded bearing from above on the right side.

Close the print head pressure lever.

What to do next

If the label material is different from the one previously used: Adjust the label sensor.

Related tasks

Positioning the label sensor

on page 72

SETTING AND MONITORING

Positioning the label sensor

About this task

Adjusting the label sensor position is necessary, if
• the machine is put into operation for the first time
• a material change takes place on wider or narrower material or on material with different punching

form/type

Procedure

Open the print head pressure lever.

Edition 1 - 8/2021

Operation

Setting and Monitoring

Содержание XLP 514





















































































































Результаты поиска

Содержание XLP 514

Отзывы:

Похожие инструкции для XLP 514

Бренды по названию

Популярные бренды

Novexx Solutions XLP 514, Руководство пользователя

Результаты поиска

Содержание XLP 514

Отзывы:

Похожие инструкции для XLP 514

Бренды по названию

Популярные бренды