Novexx Solutions XLP 514 страница 101 Скачать руководство пользователя

Страница: 101 / 116

User Manual

XLP 514/516

•

Thermal transfer printing

: after each used up ribbon roll

•

Thermal direct printing

: after each used up label roll

Procedure

Switch off the printer.

Open the front cover.

Open the print head pressure lever.

The print head flips up.

Remove material and ribbon from the printer.

Cleaning with a cleaning pen

Applying light pressure, go over the thermal edge (B) a few times with the cleaning pen (A).

Cleaning with alcohol

CAUTION!
Risk of fire due to a flammable liquid
► Observe the safety instructions on the alcohol bottle!

Moisten a lint-free cloth with alcohol (B); wipe the thermal edge (A) with the cloth.

Allow the print head to dry for several minutes.

Edition 1 - 8/2021

101

Cleaning

Cleaning the print head

Содержание XLP 514





















































































































Результаты поиска

Содержание XLP 514

Отзывы:

Похожие инструкции для XLP 514

Бренды по названию

Популярные бренды

Novexx Solutions XLP 514, Руководство пользователя

Результаты поиска

Содержание XLP 514

Отзывы:

Похожие инструкции для XLP 514

Бренды по названию

Популярные бренды