Novexx Solutions XLP 514 страница 65 Скачать руководство пользователя | Manualshive

Страница: 65 / 116

background image

User Manual

XLP 514/516

4.

Push the ribbon between the rolls sideways below the printhead.

5.

Push the ribbon rolls onto the mandrels and tighten the ribbon.

INSERTING AND REMOVING LABEL MATERIAL

XLP 51x standard: Inserting roll material

WARNING!
Danger of crushing fingers when closing the front hood.
► Always use the grip to open or close the front hood.

WARNING!
Danger of rotating parts drawing items in!
► Don´t wear loose long hair (if necessary, wear a hairnet).
► Keep loose jewellery, long sleeves, etc. away from rotating parts of the printer.
► Always close the front hood before printing.

WARNING!
The print head can become hot during operation!
► Be careful whenever touching the print head.

The illustrations in this chapter show a XLP 514. In case that the operation of the XLP 516 differs in

some points, this is indicated at the relevant point in the text

Before you begin

• Printer is stopped (“Home” screen)
• The label material is in roll form and is wound with the label side facing outwards (if this is not the

case, please note the deviating threading diagram)

Procedure

1.

Open the front hood (A).

2.

Open the print head pressure lever (picture above, B).

Edition 1 - 8/2021

65

Operation

Inserting and removing label material

«
...
63
64
65
66
67
...
»

Содержание XLP 514





















































































































Отзывы:

Нет отзывов

Похожие инструкции для XLP 514

Бренд: Zenbooth Страницы: 60

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

Бренд: LA Audio Страницы: 9

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: PARRY Страницы: 14

Бренд: York Fitness Страницы: 36

Бренд: Ultimate Healthcare Страницы: 2

Бренд: Ultimate Healthcare Страницы: 40

Бренд: Varimixer Страницы: 28

ResQCRP ResQPUMP ACD-CPR

Бренд: Advanced Circulatory Страницы: 2

Big Wheel RN1 Series

Бренд: Osborne Страницы: 8

Бренд: Kobelt Страницы: 20

Бренд: Pottinger Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды