Novexx Solutions XLP 514 страница 96 Скачать руководство пользователя

Страница: 96 / 116

User Manual

XLP 514/516

REFERENCE OF STATUS REPORTS

5001 No gap found

No gap found or several blank labels fed.
The error can have several causes:

Cause

Measure

Label sensor at the wrong position.

► Setting the position of the label light barrier

correctly (refer to user manual, chap. „Opera-

tion“ > „Setting and Monitoring“ > „Positioning

the label sensor“).

Unsuitable material inserted. No punch available

or recognizable.

► Use punched or die cut label material.

Material incorrectly inserted. Punch on the wrong

side.

► Insert material the right way round.

Wrong label length set.

EXPERTS

► Checking the punch definition in the

print job (Easy Plug: #IM).
► Checking the label length setting in the pa-

rameter menu (

Material

Label

Ma-

terial type

)

Label sensor is dirty.

► Cleaning the label sensor.

Ribbon inserted incorrectly. Ribbon runs under the

label light barrier.

► Insert ribbon correctly.

Label sensor is not sensitive enough.

EXPERTS

► Check the sensitivity setting of the

label sensor.

Label sensor is defective.

EXPERTS

► Replacing the label sensor.

After acknowledgement with key 4, the material is automatically advanced and the next punch is

searched for.

5002 Material end

There is no label web in the rear material guide that contains the material end sensor.

Possible causes

Solution

The label material is finished, i.e. the rear end of

the material web has reached the yellow material

guide in the printing module

► Load new roll of label stock

The label web runs outside of the rear material

guide, which contains the material end sensor

► Insert the label material correctly into the

material guide. Check the width adjustment of

the material guides.

Edition 1 - 8/2021

Disturbances

Reference of status reports

Содержание XLP 514





















































































































Результаты поиска

Содержание XLP 514

Отзывы:

Похожие инструкции для XLP 514

Бренды по названию

Популярные бренды

Novexx Solutions XLP 514, Руководство пользователя

Результаты поиска

Содержание XLP 514

Отзывы:

Похожие инструкции для XLP 514

Бренды по названию

Популярные бренды