Nortec EL005 Скачать руководство пользователя

Страница: 58 / 78

Installation

2582302_C_EN_1611

Nortec EL

Table 10: Modbus Communication Parameters

Parameter

Default

Software Adjustable Range

Signal type

EIA-485

–

Transmission mode

RTU

–

Baud rate

9600

110, 300, 600, 1200, 2400, 4800,

9600, 19200, 38400, 57600, 76800

or 115200

Data bits

–

Stop bits

–

Parity

Even

Odd, Even, None

Address

1-247

Time out

300 s

1-300 s

5.8.4 Connecting Multiple Units Using Linkup

The integrated controller in the Nortec EL steam humidifier allows up to six integrated controllers (for

a maximum of 12 steam cylinders) to be connected in a "main-extension" configuration using Nortec's

Linkup system. All the humidifiers within this setup must share the same location, and all linked units

will be controlled by one set of control signals connected to the main unit.

Refer to

Figure 37

and connect multiple unit using Linkup as follows:

1. Connect all control signals for the entire Linkup configuration to the low voltage terminal strip A in

the main unit.

2. Install a jumper wire between the terminal points "1" and "2" in the low voltage terminal strip on all

extension units.

3. Connect a multi-strand twisted pair shielded cable (18-24 AWG, 120 Z) between the J10 connectors

on the control board of each Nortec EL steam humidifier in the Linkup system.

IMPORTANT!

Do not reverse polarity.

4. Install the termination jumper JP8 in the control board of the last extension unit in the Linkup system.
5. Finally, refer to the Operation and Maintenance Manual to set up the multi-unit configuration in the

control software.

Содержание EL005















































































Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды

Nortec EL005, Руководство по установке

Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды