Nortec EL005 Скачать руководство пользователя

Страница: 55 / 78

Installation

Nortec EL

2582302_C_EN_1611

5.8.3.9

Remote Relay PCB Connections

The optional remote relay PCB (printed circuit board) on the Nortec EL steam humidifier has the follow

ing four potential-free relay contacts for remote display of humidifier status and fault conditions. Refer

Figure 34

for the relevant terminal contacts.

•

Error – this relay can be wired to open (NC) or close (NO) when a fault is detected by the humidifier

controls.

•

Service – this relay is activated when the set maintenance interval elapses. It can be wired to open

(NC) or close (NO) when a service warning appears on the touchscreen panel of the humidifier and

the status

LED turns yellow in color.

Note:

The way this relay handles system warnings (all warnings or service warnings only) can

be configured in the control software – refer to the Remote Fault Board tab in the Operation and

Maintenance Manual.

•

Steam – this normally open (NO) relay closes when the control board detects a current draw and

production of steam.

•

Unit on – this normally open (NO) relay closes when the humidifier has power, and the On/Off switch

is in the On position.

Figure 34:

INTERNAL

EXTERNAL

Analog Out

Sensor Supply

Max. 60m

Unit ON

Steam

Service

Error

1 2 3 4 5 6 7 8 9 10

100mA

J2 on Control Board

Remote Relay PCB Connections

The remote relay PCB connects to the connector J2 on the Nortec EL control board.

Содержание EL005















































































Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды

Nortec EL005, Руководство по установке

Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды