Nortec EL005 Скачать руководство пользователя

Страница: 56 / 78

Installation

2582302_C_EN_1611

Nortec EL

5.8.3.10 Accessory Relay PCB Connections

The optional accessory relay PCB on the Nortec EL steam humidifier has the following four potential-

free relay contacts that can be used to control other accessory devices. Refer to

Figure 35

for the relevant

terminal contacts.

•

Flush A – this normally open (NO) relay can be wired to activate or deactivate the optional valve for

flushing the water supply line for steam cylinder A.

•

Flush B – this normally open (NO) relay can be wired to activate or deactivate the optional valve for

flushing the water supply line for steam cylinder B.

•

Fan Activate B – this normally open (NO) relay can be wired to activate or deactivate an external

fan of the AHU (air handling unit) connected to steam cylinder B.

•

Fan Activate A – this normally open (NO) relay can be wired to activate or deactivate an external fan

of the AHU connected to steam cylinder A.

Figure 35:

INTERNAL

EXTERNAL

Analog Out

Sensor Supply

Max. 60m

Fan A

Fan B

Flush B

Flush A

1 2 3 4 5 6 7 8 9 10

100mA

J3 on Control Board

Accessory Relay PCB Connections (Optional)

The accessory relay PCB connects to the connector J3 on the Nortec EL control board.

Содержание EL005















































































Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды

Nortec EL005, Руководство по установке

Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды