Nortec EL005 Скачать руководство пользователя

Страница: 25 / 78

Installation

Nortec EL

2582302_C_EN_1611

Figure 10:

Optional Mounting, Large Housing

1 Mounting bar

2 Flat washer (×3)

3 Lag bolt, 1/4×2 in (×3)

4 Screw, M6

10 (×1), supplied

2. Align the holes in the mounting bar with the marks for the attachment points "A", and install the

mounting bar on the mounting surface with 1/4×2 in lag bolts and flat washers (supplied by others).

Use longer bolts if going through drywall or other structural material into the mounting surface. Level

the mounting bar before tightening the lag bolts.

3. Remove the door panels from the humidifier.

WARNING!

Heavy object – risk of injury!

The small humidifier weighs 45 lb (20 kg), and the large humidifier weights 120 lb (54 kg).
Prevention:

Use an appropriate lifting device, or request assistance to raise the humidifier into

position.

4. Carefully raise the humidifier into position, and hang it on the mounting bar.
5. Secure the humidifier to the mounting bar with the M6×10 screw (supplied),

and fasten securely.

6. Reinstall the door panels, and fasten them securely.

Dimension

Housing Size

Large

16.0 in

(406 mm)

Содержание EL005















































































Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды

Nortec EL005, Руководство по установке

Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды