Nortec EL005 Скачать руководство пользователя

Страница: 40 / 78

Installation

2582302_C_EN_1611

Nortec EL

5.6

Water Connections

Refer to

"Site Requirements" on page 15

for the water supply and drain requirements.

Read

"Water Connection Requirements" on page 38

, and perform the water connections as shown in

Figure 21

on page 36

and

Figure 22 on page 37

5.6.1 Water Connections Overview

Figure 21:

Water Supply and Drain Connections, Small and Medium Units

1 Drain canal (outlet un-threaded), 1-3/16 in (30 mm) O.D.

2 Hose clamp (supplied)

3 Flexible bent hose (supplied)

4 Drain line, minimum 7/8 in (22 mm) I.D. (not supplied)

5 Water supply line, minimum 1/2 in (13 mm) (not supplied)

6 Adaptor, 3/4 BSPP to 1/2 in NPT (supplied)

7 Fill valve (3/4 in BSPP plastic threads)

8 Air gap and optional trap (not supplied)

9 Shutoff valve (not supplied)

Filter, 5 μm (optional, but recommended)

Union fitting (not supplied)

Содержание EL005















































































Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды

Nortec EL005, Руководство по установке

Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды