Nortec EL005 Скачать руководство пользователя

Страница: 74 / 78

Appendix-B

2582302_C_EN_1611

Nortec EL

B.1.2 Performance Checklist

Complete the performance tests after inspecting the site services and the installation, then fill out the form be

low.

Note:

When filling out the form leave the checkbox un-checked if the item does not apply, or if the require

ment is not satisfied. Enter all notes and exceptions in the space provided

on page vii

Distribution System

Note:

For commissioning the distribution system itself, refer

to the individual commissioning checklist for the distribution

system.

SAM-e

Mini-SAM-e

Blower Pack

ASD/BSD/CSD

Model:

Number of XSD units:

Distance to obstruction:

(Minimum 1× absorption distance required from the

distributor to first obstruction (coil/bend ) downstream).

Distance to filter:

(Minimum distance between the distributor and filter

downstream – 1.5-2× absorption distance for class C

filter, and 2.5-3× absorption distance for sub-micron

particle filter).

Preliminary

Pre-start-up checklist completed:

Gas leakage test inside unit completed:

Check for water leaks inside unit com

pleted:
Steam cylinder seated properly in its

base:
Condensate trap inside the unit primed:

(Nortec GS CS/NX models only).

All access panels installed and fastened

securely:

Start-Up

Shutoff valve in water supply line open:

Fill tests completed successfully:

Ignition safety shutoff test completed

successfully:
Manual gas shutoff valve open:

On/Off switch set to the On position:

Software version:

Controls

Select the type of signal input connected

to the channels of the low voltage termi

nal strip #1:

(Enter setpoint value (if applicable) in the field below

the checkbox).

Demand Humidistat

(modulating)

On/Off Humidistat

Transducer

(modulating)

Digital Controls

CH 1:

CH 2:

On/Off:

If a second set of inputs is connected to

the channels of the low voltage terminal

strip #2 (on dual cylinder units running in

independent mode only), select the type

of signal input connected to the terminal

strip #2:

(Enter setpoint value (if applicable) in the field below

the checkbox).

Demand Humidistat

(modulating)

On/Off Humidistat

Transducer

(modulating)

Digital Controls

CH 1:

CH 2:

On/Off:

Control signal configuration in the soft

ware matches inputs connected to unit:

Содержание EL005















































































Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды

Nortec EL005, Руководство по установке

Результаты поиска

Содержание EL005

Отзывы:

Похожие инструкции для EL005

Бренды по названию

Популярные бренды