Nordson PermaFlo 830 Скачать руководство пользователя страница 76

Страница: 76 / 102

Air Motor Parts

D 1-5

Part 1022914G03

2007 Nordson Corporation

New Style Air Motor (Pump Revisions D and Above)

See Figure D 1-2.

Item

Part

Description

Quantity

Note

−

- - - - - -

AIR MOTOR, 8-inch, assembly

- - - - - -

SCREW, hex, cap,

−

11 x 9.50 in., steel, zinc

1063118

HEAD, cylinder, upper, 8-inch

- - - - - -

BOLT, eye,

−

16 x 0.75 in. shank, steel

1063996

KIT, actuator

1063997

KIT, 3-way valve

941080

O-RING, Buna-N, 0.250 x 0.438 x 0.094 in.

941373

O-RING, Viton, black, 2.063 x 2.25 in.

1023598

O-RING, Buna-N, 7.734 x 8.012 x 0.139 in.

1021425

CYLINDER, air, 8-inch

1063117

HEAD, cylinder, lower, 8-inch

952101

CUP, U, polyurethane, 1-

x 1-

in.

1021442

PLATE, back-up

- - - - - -

SCREW, socket,

−

20 x 0.50 in., cap

- - - - - -

NUT, hex, flanged serrated,

in., clear zinc

1021440

ROD, connecting, piston

1021428

PISTON, air, 8-inch, carboxylated nitrile

1021441

WASHER, 0.38 x 2.00 x 0.06 in., stainless steel

- - - - - -

SCREW, low head, socket,

-16 x 1.00, zinc,

nylok

1021635

VALVE, air, 4-way, 7-port, 2-position

942230

O-RING, hotpaint, 1.625 x 1.875 x 0.125 in.

- - - - - -

WASHER, lock, split, 0.25 in., stainless steel

1021444

KIT, muffler, PermaFlo

982482

SCREW, pan head, slotted, M4 x 10, stainless

steel

240976

CLAMP, ground, with wire

983047

WASHER, flat, 4 mm, stainless steel

- - - - - -

SCREW, socket set, 0.375

−

24 x 0.25 in., cup

point, stainless steel

- - - - - -

COUPLING, shaft, retainer sleeve

- - - - - -

COUPLING, shaft

1021508

STUD, air motor, PermaFlo

- - - - - -

NUT, hex, flanged serrated,

in., clear zinc

NOTE A: For parts breakdown, refer to

New Style Air Valve Parts

in this section.

B: Muffler Kit, part 1021444, includes 1 muffler, 2 screws, 2 lockwashers, and two O-rings.
C: Noted parts are included in the Coupler Kit, part 1024892.

Содержание PermaFlo 830







































































































Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды

Nordson PermaFlo 830, Руководство пользователя по изделию

Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды