Nordson PermaFlo 830 Скачать руководство пользователя страница 57

Страница: 57 / 102

Air Motor Repair

C 1-14

Part 1022914G03

2007 Nordson Corporation

Air Motor Rebuild Completion

1. See Figure C 1-12. Install the air motor on the hydraulic section.
2. Install the hex nuts (36) on the air motor studs (35) and tighten them to

136

14 N

m (100

10 ft-lb).

3. Secure the lower cylinder head (16) to the pump mounting surface.

1300387B

Customer-supplied

fasteners

TIghten to 136

14 N

(100

10 ft-lb).

Figure C 1-12 Air Motor Installation

16. Lower cylinder head
35. Air motor studs

36. Hex nuts

4. Pull down on the connecting rod until it contacts the plunger and install

the coupling as described on page C 1-2.

5. Connect the air hose to the air valve.
6. Connect the ground clamp to a true earth ground.
7. Supply compressed air to the pump and check the air motor operation.

Check for air leaks.

Air Valve Rebuild

Pumps revision D and above use a new air valve assembly. See Figure

C 1-13 for the old style air valve and Figure C 1-14 for the new style air

valve. Refer to

Section D1 Air Motor Parts

for air valve service kits and air

pilot valve part numbers.

1. Perform the

Muffler and Air Valve Removal

procedure on page C 1-6.

2. Remove the socket-head screws and end caps from the air valve.
3. Disassemble the air valve, inspect and replace any damaged

components, and reassemble the air valve.

4. If replacing the air pilot valve on a new style air valve assembly, install

the fittings and connect the air tubing as shown in Figure C 1-14.

Содержание PermaFlo 830







































































































Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды

Nordson PermaFlo 830, Руководство пользователя по изделию

Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды