Nordson PermaFlo 830 Скачать руководство пользователя страница 67

Страница: 67 / 102

Hydraulic Section Repair

C 2-8

Part 1022914G03

2007 Nordson Corporation

Solvent Cup Installation

See Figure C 2-7.

NOTE:

Do not tighten the solvent cup until you install the plunger through

the upper packings. Tightening the solvent cup expands the upper packings

and makes it difficult to install the plunger.
1. Pump revisions A

−

D: Thread the solvent cup adapter (5) into the upper

housing and tighten it snugly.

2. Thread the solvent cup (1) into the solvent cup adapter (5) (pump

revisions A

−

D), or into the upper housing (pump revisions E and above)

until the solvent cup just bottoms out against the packings.

Pressure Ball Valve Assembly

1. See Figure C 2-7. Place the flats of the pressure ball seat (10) into a

soft-jawed vise. Be careful not to damage the packings.

2. Clean the mating parts with a residue free cleaner or degreaser then

apply Loctite 242 removable thread adhesive to three to four threads all

the around the ball seat.

3. Place the small ball (9) on top of the pressure ball seat, between the

cage ears.

4. Thread the plunger (8) onto the ball seat.
5. Tighten the plunger until you feel metal-to-metal contact.

Revisions A

−

ONLY

Clean the mating parts with a

residue free cleaner or

degreaser then apply Loctite

242 removable thread

adhesive or equivalent to three

or four of the threads all the

way around.

Figure C 2-7 Solvent Cup and Siphon Check Valve Assembly

1. Solvent cup
5. Solvent cup adapter

(w/packings)

7. Upper housing

8. Plunger
9. Ball (small)

10. Pressure ball seat

(w/packings)

Note:

Item 5 used on pump revisions A

−

D only.

Содержание PermaFlo 830







































































































Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды

Nordson PermaFlo 830, Руководство пользователя по изделию

Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды