Nordson PermaFlo 830 Скачать руководство пользователя страница 62

Страница: 62 / 102

Hydraulic Section Repair

C 2-3

Part 1022914G03

2007 Nordson Corporation

Coupling Replacement

1. See Figure C 2-1. Install the coupling sleeve (A) over the connecting

rod (C), making sure the arrow on the side of the sleeve is pointing up.

2. Pull the connecting rod down until it contacts the plunger (8).
3. Install the two coupling halves (D) around the connecting rod and

plunger.

4. Slide the coupling sleeve over the coupling halves. Drive the sleeve

completely over the coupling halves with a rubber mallet.

5. Tighten the two set screws (B) with a

-in. hex wrench to

10.2

1 N

m (90

10 in.-lb).

Hydraulic Section Rebuild

The hydraulic section can be removed from the pump and rebuilt without

removing the pump from its mounting.

Preparation

1. Flush the hydraulic section with a compatible solvent.
2. Remove the coupling as described in

Coupling Removal and

Replacement

in this section.

3. Shut off and lock out the compressed air supply to the pump and relieve

the system fluid pressure.

4. Disconnect the siphon and high-pressure fluid hoses, and the air supply

hose from the air motor. Remove the circulation valve kit, if installed in

the siphon port.

Removal

1. See Figure C 2-2. Remove the customer-supplied fasteners securing

the upper housing (7) to the pump mounting surface.

2. Have someone support the hydraulic section while you remove the three

hex nuts (B) from the air motor studs (A).

3. Lower the hydraulic section off the studs.

Содержание PermaFlo 830







































































































Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды

Nordson PermaFlo 830, Руководство пользователя по изделию

Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды