Nordson PermaFlo 830 Скачать руководство пользователя страница 10

Страница: 10 / 102

Quick Reference

A 1-1

Part 1022914G03

2007 Nordson Corporation

Section A 1

Quick Reference

Introduction

Use this section for quick reference for the following information on the

PermaFlo 830

pump:

specifications

service kits

recommended spare parts

adhesives, sealants and lubricants used for service

solvent fluids

options

Refer to the following sections for more information:
Part B: Safety, Description, Installation, Operation, and Troubleshooting

Part C: Air Motor and Hydraulic Section Repair

Part D: Air Motor and Hydraulic Section Parts

Pump Revisions

The ID plate on the front of the hydraulic section contains the Nordson part

number and revision letter for each pump.

Note the revision letter of your pump before using this manual, as it may

contain reference to the revision letter or a range of revisions, if procedures

or replacement parts were affected by a revision.

Specifications

Dimensions and Weight

Dimension/Weight

PermaFlo 830

Length

918 mm (36.14 in.)

Width (revisions A

−

351 mm (13.82 in.)

Width (revisions D and above)

419 mm (16.50 in.)

Depth (front to back) (revisions A

−

391 mm (15.41 in.)

Depth (front to back) (revisions D and above)

366 mm (14.4 in.)

Weight

41 kg (91 lb)

Содержание PermaFlo 830







































































































Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды

Nordson PermaFlo 830, Руководство пользователя по изделию

Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды