Nordson PermaFlo 830 Скачать руководство пользователя страница 13

Страница: 13 / 102

Quick Reference

A 1-4

Part 1022914G03

2007 Nordson Corporation

Air Motor Kits

Refer to

Part D1, Air Motor Parts

for kit parts breakdowns.

Part

Description

Note

1024892

KIT, coupler, PermaFlo

1030558

KIT, pilot valve, PermaFlo

1063996

KIT, actuator

1063997

KIT, 3-way valve

1029057

KIT, T-seal (air valve)

1029058

KIT, spool and T-seals (air valve)

NOTE A: Pilot valve kit used only on pump revisions A

−

C that have air motors with cartridge-type air pilot valves.

C: Noted kits used only on pump revisions D and above.

Hydraulic Section Kits

Refer to

Part D2, Hydraulic Section Parts

for kit parts breakdowns.

Part

Description

Note

1027525

KIT, ball, pressure check, PermaFlo 830

1027526

KIT, ball, siphon check, PermaFlo 830

1027527

KIT, hydraulic, seal, PermaFlo 830

1063360

KIT, hydraulic, seal, PermaFlo 830

NOTE A: Use 1027527 kit for pump revisions A

−

D, and 1063360 kit for revisions E and above.

Recommended Spare Parts

Keep the following parts in inventory to avoid unplanned downtime.

Quantities listed support a single pump. Adjust order quantities based on

the number of pumps in service.

Part

Description

Quantity

Note

−

PACKING kit

1042327

PLUNGER, hydraulic, PermaFlo 830

1027525

KIT, ball, pressure check, PermaFlo 830

1027526

KIT, ball, siphon check, PermaFlo 830

1027527

KIT, hydraulic, seal, PermaFlo 830

1063360

KIT, hydraulic, seal, PermaFlo 830

1030558

KIT, pilot valve, PermaFlo

1063996

KIT, actuator

1063997

KIT, 3-way valve

- - - - - -

SOLVENT CHAMBER FLUID

As Required

NOTE A: Order correct packings for your application. Refer to

Packing Gland Materials and Applications

in this

section for more information.

B: Pilot valve kit only used on pump revisions A

−

C that have air motors with cartridge-type air pilot valves.

C: Noted kits used only on pump revisions D and above.
D: Use 1027427 kit for pump revisions A

−

D, 1063360 kit for revisions E and above.

E: Refer to

Solvent Chamber Fluid

in this section for the correct type for your application.

Содержание PermaFlo 830







































































































Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды

Nordson PermaFlo 830, Руководство пользователя по изделию

Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды