Nilfisk-Advance 56507009 Скачать руководство пользователя страница 50

Страница: 50 / 82

- FORM NO. 56043129 - SR 1900

SOLUTION SYSTEM

TROUBLESHOOTING GUIDE

Troubleshooting Guide
Symptom
Misting pump will not work
Part B: Electrical Load Circuit
Note 1: Do all testing with the key switch ON, misting solution tank not empty, main broom

lever lowered, drive pedal activated in Fwd or Rev and the M4 misting pump’s control switch

S26 turned ON.

Note 2: Before T.S.check the continuity of the pump’s circuit breaker CB 7 (10A), reset or

replace if defective.

Note 3: Check for plugged misting nozzles clean if needed.

Misting pump will not

work

Test continuity of the

CB7(10A) circuit

breaker & its wiring.

Repair or replace

defective parts.

Test for 12V’s @ the M4

misting pump wires (+

Gra/Orn & - Blk).

Test for (+)12V’s

@ the K6 Blu wire

to battery ground.

Do you have

12V’s?

Replace the

defective K6 misting

pump relay

Repair or replace the M4

misting pump.

Test for (+)12V’s

@ the K6 Gra/Orn

wire to battery

ground. Do you

have 12V’s?

Yes

On the (+) Gra/Orn

& (-) Blk M4 pump

wires check for an

open circuit.

Repair or replace

the defective wire

Yes

Содержание 56507009



















































































Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды

Nilfisk-Advance 56507009, Руководство по устранению неисправностей

Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды