Nilfisk-Advance 56507009 Скачать руководство пользователя страница 52

Страница: 52 / 82

- FORM NO. 56043129 - SR 1900

ENGINE SYSTEM

1.6 liter GM Engine Specifications

Engine type

Liquid Cooled, 4 Cylinder, Single Overhead cam

Distributor-less

Displacement

98 Cubic inches (1600 cc)

Fuel Gasoline

87 Octane Unleaded Gasoline with no more than

10% Ethanol by volume

Fuel LP

33 Lbs. Tank Size (liquid withdrawal system)

Spark Plugs

AC DELCO PN 93206675, Gap .032 -.035 (.8 mm-.9 mm)

Spark Plug wiring

Match Numbered Coil Position to Spark Plug

Number (front to rear 1, 2, 3 & 4)

Engine Firing Order

1-3-4-2

Ignition Timing

Fixed (controlled by engine ECM)

Engine Rotation

CCW (flywheel end)

Valve lifters

Hydraulic

Oil Capacity

3.7 qts. (3.5L) with Oil Filter

Oil Pressure

21 PSI (minimum with engine hot at idle)

Cooling System

3.5 qts. (Engine Only)

ROUTINE ENGINE MAINTENANCE

• Keep the fuel tank filled. This helps to reduce condensation and moisture entering the fuel system (gasoline).

• Make daily checks of the engine oil and coolant levels.

• Repair any oil or coolant leaks immediately.

• Check condition of battery (water level) and cables weekly.

• Keep the engine air filter clean.

• Observe the engine coolant temperature gauge frequently.

• Observe the engine oil pressure gauge frequently.

• Check the voltmeter and charging system.

Содержание 56507009



















































































Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды

Nilfisk-Advance 56507009, Руководство по устранению неисправностей

Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды