Nilfisk-Advance 56507009 Скачать руководство пользователя страница 37

Страница: 37 / 82

FORM NO. 56043129 - SR 1900 -

SWEEPING SYSTEM

TROUBLESHOOTING GUIDE

Troubleshooting Guide
Symptom
Side broom(s) will not raise or lower.
Mechanical and Hydraulic functions
Note 1: Do all testing with the engine running at high speed, the main broom lowered (sweep

position) and the drive pedal activated (machine moving).

Note 2: The main broom magnetic switch S2 must be open and also the hopper interlock

switch S4 closed. for the main broom system (motors) to run. Operating the main broom will

automatically lower the side brooms. Press the side broom off button or raise the main broom

lever to raise the side brooms.

Side Broom(s) will not Raise

or Lower

Mechanical & Visual Checks
Inspect for possible

mechanical binding of:
• Side broom motor mount &

lift arm linkage damaged.
• Side broom lift cylinder rod

bent, rod oil seal leakage.

Hydraulic Checks
Possible internal blockage of

the side broom hydraulic

circuit oil path. * Remove,

Inspect & clean manifold

circuit components & hoses.
• @ port D the pilot check

valve and the pilot valve

cartridge.
• @ port F the L3 valve

cartridge, oil return to tank

circuit.
• Blockage @ Side broom

cylinder hose inlet & outlet

fittings

* Note: See hydraulic system manual section for system specifications and

troubleshooting information.

Содержание 56507009



















































































Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды

Nilfisk-Advance 56507009, Руководство по устранению неисправностей

Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды