Nilfisk-Advance 56507009 Скачать руководство пользователя страница 32

Страница: 32 / 82

- FORM NO. 56043129 - SR 1900

STEERING SYSTEM

STEERING SYSTEM TROUBLESHOOTING OVERVIEW

See Figure 1. A hydraulic steering unit, with the steering wheel mounted to it, controls the steer cylinder. The steering unit runs off the auxiliary

pump assembly. The oil flows through a priority divider built into the manifold block assembly that divides the pump output and reduces the oil flow

to 2.0 GPM for the steering system. There is a check valve built into the steering unit that allows for manual steering if there is no hydraulic oil flow

to the unit. The relief valve for the steering system is located in the steering unit and is set to open at 1100 PSI.

Steering System Hydraulic Diagram

TROUBLESHOOTING GUIDE

Problem

Possible cause

Slow steering, hard steering or loss of

Priority flow divider not providing 2.0 GPM.

Power assist.

1100 PSI relief valve open or

malfunctioning.

Steering wandering.

Loose or leaking cylinder piston packing.

Steering control unit worn.

Steering wheel turns freely

Problem with steering column

without moving wheel.

Shaft or spline.

Steering binding.

Steer cylinder loose.

FIGURE 1

Содержание 56507009



















































































Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды

Nilfisk-Advance 56507009, Руководство по устранению неисправностей

Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды