Nilfisk-Advance 56507009 Скачать руководство пользователя страница 28

Страница: 28 / 82

- FORM NO. 56043129 - SR 1900

Troubleshooting Guide
Symptom
Part1: Diesel engine will crank but not start
Note1: Always use (activate) the glow plugs circuit to start an engine that is not up to its

operating temperature.

Note 2:Before troubleshooting inspect the 10A CB5 circuit breaker.

Glow plug circuit T.S.

Check voltage @ each

glow plug terminal B+ to

Battery ground. Is the

reading close to battery

voltage ?

Test for open circuits in the

Pos.(+) feed wire and glow

plug key switch circuit.

Repair or replace defective

parts.

Test each glow plug

for an open circuit. The

resistance spec is .9

Ohms. Do any of the

glow plugs test open ?

Is the fuel tank empty?

Add fuel & air bleed

the fuel system.
Loosen air vent on fuel

filter then next @ the

fuel injection pump

w/engine cranking, but

bleed separately.
Does engine start ?

With the engine

cranking test for 12V

@ the fuel pump.

With the engine cranking

test for 12V (+) @ oil

pressure SW S28,

Gra/Brn wire to Bat. Grd.

Remove fuel line to

injector pump, crank

engine , is fuel

pumping?

Test the key SW

accessory output &

circuit wiring to the Com

terminal @ S28. If no

voltage repair or replace

bad parts. If voltage input

is OK replace the oil

pressure switch (S28)

Replace the open

defective glow plug(s).

Does fuel pump run

Replace defective fuel

pump

Loosen injector line

@ injector, crank

engine, check for

fuel.

•

See part #2

Governor/fuel control

actuator

troubleshooting.

•

See Kubota engine

Service manual check

engine compression,

injector pump, fuel

quality etc. as further

causes.

Fuel System T.S.

Yes

Test fuel pump B-

Ground wiring & repair

Yes

ENGINE SYSTEM

TROUBLESHOOTING GUIDE

Содержание 56507009



















































































Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды

Nilfisk-Advance 56507009, Руководство по устранению неисправностей

Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды