Nilfisk-Advance 56507009 Скачать руководство пользователя страница 24

Страница: 24 / 82

- FORM NO. 56043129 - SR 1900

ENGINE SYSTEM

TROUBLESHOOTING GUIDE

Troubleshooting Guide
Symptom
GM 1.6L 4 cylinder engine will not crank
Part B: Electrical Control and Load Circuit
Note 1: To test the key switch must be in start position and the foot-pedal in neutral. Also

reference Note: A below.

Note 2: Before T.S. check the CB1 60 Amp circuit breaker & 12V’s @ key switch Bat. Terminal.

Note 3: Before T.S. check battery voltage @ starter main load red wire input.

Continued from previous

page

Test for 12V @ the pink K4

coil wire to Grd. With the key

on.

Test electrical items

below
•CB5 10A breaker
•Pink & Org/Grn

ignition wiring

continuity.
•12V power to

ignition switch &

circuit functions of

start & ignition

terminals.
Repair and replace

as needed.

@ the K4 relay coil test for

12v(-) from the Gra/Wht wire

to Bat (+) with key on.

Before testing the drive pedal

sensor R2 follow the

instructions located in the

programmable control

options section to

synchronize the pedal’s

neutral dead band

adjustment. Test the drive

pedal sensor R2 (5K Ohms)

and wiring harness circuit.

Does the sensor test good ?

Substitute a new A2 control

box assembly.
See:

Note A

Repair or replace the

defective R2 drive

pedal sensor.
See:

Note A

Note A:

Any time the machines hydrostat mounted neutral position sensor is replaced or the

hydrostat linkage adjusted its neutral position must be re-programmed. Also any time the A2

control box is replaced it must be re-programmed. See the programming options section in this

manual for instructions.

Yes

Содержание 56507009



















































































Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды

Nilfisk-Advance 56507009, Руководство по устранению неисправностей

Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды