Nilfisk-Advance 56507009 Скачать руководство пользователя страница 34

Страница: 34 / 82

- FORM NO. 56043129 - SR 1900

SWEEPING SYSTEM

TROUBLESHOOTING GUIDE

Troubleshooting Guide
Symptom
Main broom motor will not run
Part B: Hydraulic Load Circuit
Note 1: Do all testing with the engine running at high speed, the main broom lowered (sweep

position) and the drive pedal activated (machine moving).

Note 2: The main broom magnetic switch S2 must be open and also the hopper interlock

switch S4 closed, for the main broom system (motors) to run.

Main broom motor

will not run

Remove and disassemble
• L2 main broom motor valve

cartridge
• Inspect, clean and reinstall

Does the motor run ?

Replace the

defective L2

main broom

control valve

cartridge.

Does the motor

run ?

Replace the

main broom

motor

Inspect the main

broom motor drive

lug and sweeping

broom inserts for

mechanical damage

Make repairs to

damaged parts.
Does the main

broom motor run

(turn) ?

Yes

Содержание 56507009



















































































Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды

Nilfisk-Advance 56507009, Руководство по устранению неисправностей

Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды