Nilfisk-Advance 56507009 Скачать руководство пользователя страница 30

Страница: 30 / 82

- FORM NO. 56043129 - SR 1900

ENGINE SYSTEM

TROUBLESHOOTING GUIDE

Troubleshooting Guide
Symptom
Diesel engine will not run at high speed
Note: With the engine running at idle press the engine speed switch to activate the high speed

engine function.

Diesel engine will not

run at high speed

Test for 12V’s (+) at the

Apec 3000 governor

speed select (1) input

terminal (Gra/Blu) to

battery (-) Grd.

Press on & off the

engine speed switch,

check for continuity @

ribbon connector (*)

pins J3-1 & J3-2 on the

A2 control box

assembly.

Ribbon pin’s

test open.

Replace the

touch pad

switch panel.

Check for

12V’s (+) @

the A2 control

box output pin

J1-17

(Gra/Blu) to

Bat (-). Grd.

Replace the

A2 control box

assembly.

Repair or replace the

defective Gra/Blu wire.

Yes

Test the governor

controller actuator

output voltage, wire

colors Wht & Wht/Blk.

@ idle approx. 4.35 V

@ High speed 5.10 V.

Is there a voltage

increase from idle to

HS with a load?

Substitute a good

known working

actuator if engine runs

properly @ both idle &

HS replace actuator.

Substitute a good

known working

governor if engine

runs properly @

both idle & HS

replace governor.

Yes

* Ribbon connector see Electrical System Figure 1 for detail pin call-outs.

Содержание 56507009



















































































Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды

Nilfisk-Advance 56507009, Руководство по устранению неисправностей

Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды