Nilfisk-Advance 56507009 Скачать руководство пользователя страница 48

Страница: 48 / 82

- FORM NO. 56043129 - SR 1900

HOPPER SYSTEM

TROUBLESHOOTING GUIDE

Troubleshooting Guide
Symptom
Hopper dump door will not operate open or close
Part B: Hydraulic Load Circuit
Note: To test the engine must be running at high speed and the hopper door (open/close)

switches pressed and held.

Dump door will not

operate open or close

Replace the

hydraulic

hopper door

cylinder

Inspect for possible

mechanical binding at:
•Dump door & hopper

frame opening
•Dump door cylinder &

linkage

Repair or replace

damaged parts. Does

the door function ?

* Remove &

disassemble the:

•L1 dump door open

•L7 dump door close

Cartridge valve

•Inspect, clean and

reinstall

Does the door

function?

Replace the

defective

•L1 door open

• L7 door close

cartridge valve.

Does the door

function ?

Yes

*Note: The engine must be shut off to remove and disassemble any valve

cartridge.

Содержание 56507009



















































































Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды

Nilfisk-Advance 56507009, Руководство по устранению неисправностей

Результаты поиска

Содержание 56507009

Отзывы:

Похожие инструкции для 56507009

Бренды по названию

Популярные бренды