Nilfisk-Advance 13300113, Руководство пользователя

Страница: 148 / 214

ENGLISH
USER MANUAL
32 33018305(3)2010-01 A RS 851
DUST CONTROL SYSTEM NOZZLE AND FILTER CLEANING
WARNING!
Protect body parts (eyes, hair, hands, etc.) properly, when performing cleaning procedures using compressed
air or water gun.
Preliminary operations
Engage the parking brake (13, Fig. E). 1.
Turn the ignition key (24, Fig. D) to OFF position and remove it. 2.
Cleaning of nozzles and fi lters on side brooms
Unscrew the ring nuts (1, Fig. AA). 3.
Remove and clean the nozzles (2, Fig. AA) and fi lters (3) with compressed air. Remove calcium deposits. If necessary, replace 4.
the fi lters (3).
Install the fi lters and nozzles, and secure them with the ring nuts. 5.
Cleaning of nozzles and fi lters in the suction pipe, from suction inlet to hopper
Empty the hopper (7, Fig. G); if it contains a small quantity of waste, it is not necessary to dump it. 6.
Drive the machine on a solid and level ground, then engage the parking brake (13, Fig. E). 7.
Lift the hopper (7, Fig. G), according to the procedure shown in the relevant paragraph. 8.
Turn the ignition key (24, Fig. D) to OFF position and remove it. 9.
To avoid that the hopper lowers by accident, install the lifted hopper support rods (3, Fig. F), according to the instructions 10.
shown on the relevant paragraph.
Operating inside the suction pipe (6, Fig. F), with a 0.55 in (14 mm) socket wrench (1, Fig. AB), unscrew the nozzle (2, Fig. AB,
11.
AC) and remove the fi lter (3) (check the actual position of the nozzle).
Clean the nozzle (2, Fig. AB, AC) and fi lter (3) with compressed air. Remove calcium deposits. If necessary, replace the fi lter 12.
(3).
Install the
fi lter and nozzle in the reverse order of removal. 13.
Remove the lifted hopper support rods (3, Fig. F) and lower the hopper (7, Fig. G) (see the procedure in the relevant 14.
paragraphs).
Cleaning of nozzle and fi lter in the rear suction pipe (optional)
Loosen the clamp (1, Fig. AD) and separate the rigid part of the rear suction pipe (2) from the hose (3). 15.
Operating inside the pipe (2, Fig. AD), with a 0.55 in (14 mm) socket wrench, unscrew the nozzle (4) and remove the fi lter (5) 16.
(check the actual position of the nozzle).
Clean the nozzle (4, Fig. AD) and
fi lter (5) with compressed air. Remove calcium deposits. If necessary, replace the fi lter (5). 17.
Install the fi lter and nozzle in the reverse order of removal. 18.
Install the hose (3, Fig. D) on the rigid part of the rear suction pipe (2) and secure with the clamp (1). 19.
DUST CONTROL SYSTEM WATER FILTER CLEANING
WARNING!
Protect body parts (eyes, hair, hands, etc.) properly, when performing cleaning procedures using compressed
air or water gun.
NOTE
When the fi lter is removed, the water inside the tanks comes out. It is advisable to perform this maintenance procedure
when the tanks are empty.
Engage the parking brake (13, Fig. E). 1.
Turn the ignition key (24, Fig. D) to OFF position and remove it. 2.
Operating over the right side of the rear axle, unscrew the water fi lter cover (1, Fig. Z) and remove it together with the fi lter. 3.
Separate the fi lter (2, Fig. Z) from the cover (3), then wash and clean them. If necessary, replace the fi lter. 4.
Install the fi lter and the cover. 5.