Nice SlideSmart CNX 15 Скачать руководство пользователя

Страница: 39 / 48

SLIDESMART CNX 15 BASIC MANUAL

www.hysecurity.com

Table 3. SmartCNX Controller - Troubleshooting

Display

Condition

Description

Alert, Error or

Fault

Possible Causes

Solutions

ALERT 22

INTLOCK FAILURE

Interlock/
Sequential Gate
communication
lost.

Alert auto
clears when
communication
between two
operators is
restored.

Appears when communication

connection is lost for more than 5

seconds between interlocked or

sequenced gate operators.

Solo operator has Sequential gate

set to ON.

1. Check cable

connections and

wiring. Make sure

both operators are

working properly

with same, current

software versions.

2. Verify Sequential

Gate is set to (0) on a

solo operator.

ALERT 28

BATTERY
DISCONNECTED

Battery
disconnected from
drive module.

Dead or disconnected batteries
detected by SmartCNX Controller.

Operator may still function on AC power

but will not have battery backup. Battery
fuse may be blown.

Replace or reconnect
batteries. Replace fuse if
needed.

FAULT 1

MOTOR RUN

TIME

(SWING ONLY)

The motor is on
longer than the
maximum run time
selected.

Taper clamp slipping

Missing target or bad limit sensor

1. Tighten taper clamp.

2. Check limit sensors.

Replace as required.

3. Increase Max Run

Timer.

FAULT 2

PHOTO EYE

Photo eye is
missing or not
working.

This fault can only occur if monitored
sensor check fails.

Correct malfunctioning
photo eye.

FAULT 4

GATE NO LOAD

SmartCNX
Controller detects
no load on
operator. Gate is
non-operational
while this fault is
triggered.

Possible causes:

Motor wires disconnected.

DC switch off.

Arm assembly disconnected

Taper clamp too loose

1. Check DC motor

wires condition and

connection to drive

module.

2. Turn DC power

switch on.

3. Tighten taper clamp.

4. Press RESET to clear

fault.

FAULT 14
STUCK GATE

SmartCNX
Controller could
not overcome
stuck gate after 3
attempts. Gate is
non-operational
while this fault is
triggered.

Caused by broken gate hardware or ice/
snow buildup.

1. Check and correct

gate hardware as

required.

2. Press RESET to clear

fault.

TROUBLESHOOTING/ALERTS/FAULTS/ERRORS

Содержание SlideSmart CNX 15

















































Результаты поиска

Содержание SlideSmart CNX 15

Отзывы:

Похожие инструкции для SlideSmart CNX 15

Бренды по названию

Популярные бренды

Nice SlideSmart CNX 15, Инструкция по установке и программированию

Результаты поиска

Содержание SlideSmart CNX 15

Отзывы:

Похожие инструкции для SlideSmart CNX 15

Бренды по названию

Популярные бренды