manualshive.com logo in svg

Nice SlideSmart CNX 15, Инструкция по установке и программированию, Страница: 3 / 48

Поделиться
Скачать
Nice SlideSmart CNX 15 Скачать руководство пользователя страница 3

MX4779 REV. A     ©2019

SLIDESMART CNX 15 BASIC MANUAL

www.hysecurity.com

     3

SAFETY REQUIREMENTS

SAFETY MESSAGES

The safety messages below inform you about potential 
hazards that can result in injury. Safety messages 

specifi cally address level of exposure to operator and are 

preceded by one of four words: 

DANGER, WARNING, 

CAUTION 

or 

NOTICE.

  DANGER

Indicates a hazardous situation which, if not avoided, 

WILL

 result in 

DEATH

 or 

SERIOUS INJURY.

  WARNING

Indicates a hazardous situation which, if not avoided, 

COULD

 result in 

DEATH

 or 

SERIOUS INJURY.

  CAUTION

Indicates a hazardous situation which, if not avoided, 

COULD

 result in 

MINOR

 or 

MODERATE INJURY.

  NOTICE

Addresses practices not related to personal injury. 

Indicates damage to equipment is probable if the 

hazardous situation is not avoided.

COMMON INDUSTRIAL SYMBOLS

These international safety symbols may appear on 
product or in its literature to alert of potential personal 

injury hazards. Obey all safety messages that follow these 

symbols to avoid possible injury or death.

Symbol

Safety Hazard

Attention -

Take Notice

Danger -

Keep Away

Entrapment Zone

Possible Pinch Point

Содержание SlideSmart CNX 15

















































Отзывы:

Нет отзывов