Nice SlideSmart CNX 15, Инструкция по установке и программированию, Страница: 29 / 48

MX4779 REV. A ©2019 SLIDESMART CNX 15 BASIC MANUAL www.hysecurity.com 29
ENTRAPMENT SENSOR WIRING
†
= Indicates default
Install the edge sensor:
1.
Install the edge sensor in an appropriate location for
entrapment protection (page 9).
2.
Set AC and DC switches OFF.
3.
Route the wires to the inside of the CNX chassis
(Figure 7).
4.
Install the wires into Sensor #1 or Sensor #2 on the
SmartCNX controller (Figure 32).
5.
Set AC and DC switches to ON.
6.
In PROGRAMMABLE INPUTS menu, select the
SENSOR TYPE for each external entrapment sensor.
The indicator LED changes to green when sensor is
activated or not installed correctly.
7.
In ENTRAPMENT SENSOR RESPONSE menu, set the
desired response action for each entrapment type.
8.
Test the function of each sensor.
Install a non-BlueBUS photo eye:
Additional photo eyes can connect to the SmartCNX
Controller terminals Sensor 1 - 2 and Input 1 - 3. Follow
the same instructions for an edge sensor.
Figure 32. Sensor Connection
HySecurity provides one edge sensor typically used as
hardwired EDGE OPEN.
PROGRAMMBLE
INPUTS
EMERGENCY INPUT 0 EMERG CLOSE
1 FIRE DEPT OPEN
SENSOR #1 TYPE 1 NOT USED
2 EYE CLOSE
3 EDGE CLOSE
4 EYE OPEN
5 EDGE OPEN
6 EDGE BOTH
SENSOR #2 TYPE “SEE SENSOR #1 TYPE”
INPUT #1 TYPE 0 (0.0 SECS)
1 NOT USED
2 EYE CLOSE
3 EDGE CLOSE
4 EYE OPEN
5 EDGE OPEN
6 EDGE BOTH
7 NOT USED
8 NOT USED
9 OPEN INTERLOCK
10 TIME CLK OPEN
11 NOT USED
12 BLK FREE EXIT
13 EXIT LOOP
14 INSIDE LOOP
15 OUTSIDE LOOP
16 CENTER LOOP
INPUT #2 TYPE “SEE INPUT #1 TYPE”
INPUT #3 TYPE “SEE INPUT #1 TYPE”
†
†
(1
†
)
(1
†
)
(1
†
)
†
Table 1. Sensors Tested for Use with HySecurity Operators
Mfg. Part # Mfg. Details
10k or 4-Wire
Pulsed
Hysecurity Part #
Photo Eyes
(Retrorefl ective)
E3K-R10K4-NR Omron 40 ft max range limit 10k MX000999
NIR-50-325 EMX 45 ft max range limit 10k
IRB-RET EMX 53 ft max range limit Both
E-931-S50RRGQ Seco-Larm 46 ft max range limit 10k
Photo Eyes
(Through-Beam)
IRB-MON EMX 65 ft max range limit 10k MX3990
E-960-D90GQ Seco-Larm 90 ft max range limit 10k
BlueBUS Nice 65 ft max range limit
Edge Sensors
Sentir Series ASO Safety
Channel mount, high profi le
Channel mount, low profi le
Round, wraparound
Square, wraparound
10k
AS1502-0440-05
AS1502-0430-05
AS1501-0760
AS1501-0790
CPT210-2U-#-T2 Miller Edge
10k resistor termination
(replace # with length
requirement in feet)
10k
Edge, Wireless
Kits
iGAZE RE Kit
Transmitter
Solutions 50 ft line of sight max range
limit
10k
WEL-200 (kit
with receiver and
transmitter) EMX
200 ft line of sight max
range limit
Both
COMPATIBLE EXTERNAL SENSORS
Note: Additional entrapment sensors can connect to Sensor 1 - 2 and Inputs 1 - 3
An example wiring diagram is shown below for a non-contact sensor (photo eye). Set any DIP-switches and jumpers according
to manufacturer instructions for 10k normally open.
Example wiring for the EMX IRB-MON transmitter and receiver.
NOTICE
The SmartCNX Controller inputs use 10k or 4-wire pulsed monitoring. Connect sensor using normally open connections.
The SmartCNX Controller does not support normally closed inputs.