Nice SlideSmart CNX 15 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 48

Nice SlideSmart CNX 15 Скачать руководство пользователя страница 18

18

www.hysecurity.com

SLIDESMART CNX 15 BASIC MANUAL

MX4779 REV. A ©2019

ATTACH TARGET MAGNET AND CHAIN COVER

The SlideSmart CNX requires one target magnet as
a "home position" for the software's gate position
monitoring. Two limit sensors are provided, but only
one is used depending on operator handing.

1.

Set the AC and DC switches to OFF.

2.

Push the gate to the full CLOSED position.

3.

Attach the target magnet to a fixed link between

the sprocket and the idler furthest from the gate

opening. Point the magnet towards the operator.

LEFT HAND

GATE CLOSED

TARGET

MAGNET

OPENS THIS

DIRECTION

LIMIT

SENSOR

RIGHT HAND

GATE CLOSED

TARGET

MAGNET

OPENS THIS

DIRECTION

LIMIT

SENSOR

Figure 14. Limit Sensor and Target Magnet Position

Figure 15.

Target Magnet Toward Operator

Attached to a Fixed Link

1. Align the chain cover tabs to the rear cover slots

and then push down to snap it in place.

2. For additional safety, install the lock pin to

prevent easy removal of the chain cover.

Figure 16. Attach Chain Cover

Figure 17. Install Spring Pin

«
...
16
17
18
19
20
...
»

Содержание SlideSmart CNX 15

















































Отзывы:

Нет отзывов