Nice SlideSmart CNX 15 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 48

Nice SlideSmart CNX 15 Скачать руководство пользователя страница 20

20

www.hysecurity.com

SLIDESMART CNX 15 BASIC MANUAL

MX4779 REV. A ©2019

WIRING AND POWER

1. Make sure both the DC and AC power switches

are in the OFF position.

2. Connect the battery harness to the back right

hand corner of the drive module. (Figure 20)

3. Remove the junction box cover. (Figure 21)

4. Connect the incoming power supply wires to the

AC or DC (solar) terminal block inside the junction

box. Match the wire colors. (Figure 22)

5.

Organize all the wire connections and put the

cover onto the junction box.

Note: For 208V/230V or solar (24V) installations,

place the label (included in the ship with kit)
over the factory default 115V 1Ø label.

6. For solar installations, remove the power switch

mounting plate and disconnect the DC wires

from the power supply. Tape or wire nut the ends

separately to prevent shorts (Figure 23).

Note: CNX operators require 24VDC rated solar

panels with a maximum open circuit voltage
of 48VDC.

7.

Set both AC and DC power switches to ON

8. Software version will appear on LCD display and

then the Setup Menu.

Figure 20. Battery Harness to Drive Module

Figure 21. Junction Box Cover

Figure 22. 115VAC/230VAC and Solar DC Terminals

DANGER

Turn off AC power at the source (circuit breaker

panel) before accessing the wires in the CNX

junction box. Follow facility Lock Out/Tag Out

procedures.

G

L

N

L

G

N

L

G N

Blue
(-)

Red

(+)

Blue
(-)

Red

(+)

Connect service outlet lead wires to 115VAC only.

AC

SOLAR

Figure 23.

Disconnect DC Power Supply Wires

Figure 24.

Set Both Power Switches to ON

«
...
18
19
20
21
22
...
»

Содержание SlideSmart CNX 15

















































Отзывы:

Нет отзывов