manualshive.com logo in svg

Nice SlideSmart CNX 15, Инструкция по установке и программированию, Страница: 35 / 48

Поделиться
Скачать
Nice SlideSmart CNX 15 Скачать руководство пользователя страница 35

MX4779 REV. A     ©2019

SLIDESMART CNX 15 BASIC MANUAL

www.hysecurity.com

     35

TROUBLESHOOTING/ALERTS/FAULTS/ERRORS

Table 3. SmartCNX Controller - Troubleshooting

Display 

Condition

Description 

Alert, Error or 

Fault

Possible Causes

Solutions

SAFE MODE

Safe Mode Alert

Occurs when an edge sensor or Inherent 

Entrapment Sensor (IES) trips. Gate 
binding, wind, or a faulty edge sensor 
can cause a false alert.

1.  Press RESET or 

either STOP button.

2.  Remove obstruction.

3.  Correct gate 

hardware.

4.  Correct faulty edge 

sensor.

5.  Adjust IES sensitivity.

ENTRAPMENT 

MODE

Entrapment Mode 
Alert

Occurs when IES is tripped when gate 

is already in Safe Mode (two IES trips in 

one cycle). Operator will not function 

until it is reset, which can occur by:

 

z

An Open or Stop command from a 

push-button control

 

z

Pressing STOP button on operator 

side

 

z

Pressing RESET button below display

Gate binding, wind, or a faulty edge 
sensor can cause a false alert.

Refer to solutions above.

NO AC POWER

No AC Input 
Power Advisory 
only.

AC power is shut off at source (breaker) 
or is not connected. AC power switch on 
operator (lower rocker switch) is turned 
off, or circuit breaker on the operator 
has tripped. Bad power supply. Power 
supply selector switch is in the wrong 
position.

1. 

Set AC switch to On.

2.  Reset operator 

circuit breaker or 

reset circuit breaker 

at electrical panel.

3.  Verify AC power to 

operator. Have a 

licensed electrician 

check wiring.

4.  Check power supply 

output is 36VDC.

Содержание SlideSmart CNX 15

















































Отзывы:

Нет отзывов