Nice SlideSmart CNX 15 Скачать руководство пользователя страница 23

Страница: 23 / 48

SLIDESMART CNX 15 BASIC MANUAL

www.hysecurity.com

INITIAL SETUP

CONFIGURE THE SETUP MENU (SLIDE)

The first time the SmartCNX controller powers on

set USAGE CLASS, GATE HANDING, and LEARN
LIMITS before normal operation.

Set the AC and DC switches to ON the first time.

Software version appears on the display and

then USAGE CLASS - 0.

2. Press SELECT, press the UP or

DOWN

arrow to

navigate to the correct USAGE CLASS (page

6), and press SELECT to accept value.

3. Press the UP or

DOWN

arrow until GATE

HANDING appears on the display, press SELECT,

press the UP or

DOWN

arrow to navigate to

the correct option, and press SELECT to accept

value.

STARTING UP flashes on the display, then

LEARN LIMITS appears.

5. Hold the

OPEN

button until the gate slides to

full open. Release the

OPEN

button.

Note: Press

to reverse direction.

Note: Do not set limits at the physical OPEN and

CLOSE stop. Leave a 1 to 2 inch (2.5 - 5 cm)

gap to allow slack in the chain to prevent wear
and avoid stress on gate hardware.

6. Press SELECT twice to store the full open

location in memory.

7. Hold the

button until the gate slides to

full close. Release the

button.

Note: Press OPEN to reverse direction.

8. Press SELECT twice to store the full close

location in memory.

GATE CLOSED appears on the display. ALERT

15 flashes until the limit sensor detects the target

magnet on the next open cycle.

Note: NO AC POWER flashes if the AC power is not

connected or the AC power switch is set to

OFF

10.

Press OPEN and then CLOSE to cycle the

gate. An audible beep and both OPEN and

CLOSE limit LEDs flash when the target is first

recognized on the close cycle.

NAVIGATE THE MENUS

Press MENU/BACK to enter the menus or to exit
the current screen (up one level without saving any
changes).

Press the UP or DOWN arrow to change the current
selection until you find the one you want.

Press SELECT to access the menu or sub-menu.
Press SELECT to accept the current option or value.

Note: These navigation instructions are the same

throughout the SmartCNX controller menus.

HYSECURITY

B.1.00

1 , 2 , 3 , 4

USAGE CLASS

0 , 1 (RIGHT) , 2 (LEFT)

GATE HANDING

LEARN OPEN

INCHES: +000.0

LEARN CLOSE

INCHES: +000.0

HYSECURITY

GATE CLOSED

0 - No Handing set. Gate will not move until

handing is set.

1 - Viewing from operator side, gate opens to

the right

2 - Viewing from operator side, gate opens to

the left

Figure 27.

Configuring Setup Menu

Содержание SlideSmart CNX 15

















































Результаты поиска

Содержание SlideSmart CNX 15

Отзывы:

Nice SlideSmart CNX 15, Инструкция по установке и программированию, Страница: 23 / 48

Результаты поиска

Содержание SlideSmart CNX 15

Отзывы: