manualshive.com logo in svg

Nice SlideSmart CNX 15, Инструкция по установке и программированию, Страница: 15 / 48

Поделиться
Скачать
Nice SlideSmart CNX 15 Скачать руководство пользователя страница 15

MX4779 REV. A     ©2019

SLIDESMART CNX 15 BASIC MANUAL

www.hysecurity.com

     15

Figure 6. Conduits and Earth Ground

Figure 7. 

Preferred Control Wire Routing to SmartCNX Controller

PREPARE AN INSTALLATION SITE

CONDUITS STUBBED

MIN. 2” ABOVE PAD

GROUND LEVEL

INCOMING

HIGH VOLTAGE

VEHICLE

LOOP

CONTROL

WIRES

LOW VOLTAGE/

COMMUNICATION

WIRES

PRIMARY/SECONDARY

WIRES - OPTIONAL

EARTH

GROUND

CONDUIT

3 FOOT

(91cm)

MAXIMUM

Earth

Ground

rod & wire

Consult local

codes for

proper depth

The potential for

lightning discharge

exists with all gates, fences, and

gate operators. National Electric

Code (NEC) requires a separate

earth ground in addition to the

required equipment ground. A local

earth ground also serves to protect 

the electronic controls.

DANGER

NOTE: 

To reduce electrical

interference, keep as much distance

as possible between the high voltage

and low voltage conduits. 

ROUTE 6 AWG

EARTH GROUND

WIRE THROUGH

CONDUIT AND

ATTACH TO

PROVIDED

GROUND LUG

HySecurity requires a concrete pad 
with a minimum 2 inch extension above 
ground and a pad depth of 16 inch or 
at least to the frost line, whichever is 
deeper. Follow local building codes to 
identify the frost line.

Содержание SlideSmart CNX 15

















































Отзывы:

Нет отзывов